KHK Catalog 3011 Corrections

Page	Item	Correction	Detected Date of Error	KHK Catalog VOL
P40	MSGA1.5-15	Correction in Outside diameter ~~22.5~~ --> 25.5	11.10.04	.
P52	SSG 0.5 and 0.8 products	Correction in Tooth hardness ~~225 to 260HB~~ --> 200 to 270HB	11.10.19	.
P270,P272	DSL Acetal Fairloc Hub Spur Gears	A caution note was missing. The line below was added. "Holding strength between the teeth (acetal) and the core (SUS303) is 2.9N・ｍ for all DSL products. Please consider the holding strength when selecting products."	11.09.30	.
P353 - 361	The caution note No.3 described at “Caution on Secondary Operations “	~~straightened and annealed~~ → stress relief annealed	11.04.05	.
P372	The data of “Heat Treatment” in the Characteristic Table	~~Straightened & annealed~~ --> " - "	11.04.05	.
P382 - 418	The data of “Heat Treatment” in the specification tables	~~Stress relief annealing~~ -->" - "	11.04.05	.
P390	Shape diagram for SRS Products	Although there is a groove (approx.1mm) at the foot, it does not cause problems functionality-wise. →	11.06.30	.
P400	The data of “Heat Treatment” in the Characteristic Table	~~Straightened & annealed~~ --> " - "	11.04.05	.
P432	SMS1.5-25L/R Products Outside diameter and Crown to back length	Outside diameter : ~~39.30~~ --> 39.31 Crown to back length : ~~16.15~~ -->16.16	11.09.30	.
P434	The item “Bore” in the Dimension Table for Zerol Miter Gears	A --> A H7	11.05.16	.
P438	Diagram for B1-Shaped LM Miter Gears	The tooth width shown in the diagram was incorrect and was revised as follows.There is no correction in the data for tooth width and the allowable torque shown in the dimension table. corrected to -->	11.12.14	.
P446	DM products	Correction in Bore ~~AH7~~ --> A	11.11.9	.
P468,469	Helix hands of SBS products	The helix angles for the following products were incorrect. Product: SBS1.5-6015R, 1560L, SBS2-6015R and 1560L ~~35°~~ --> 39° Also, the data for the allowable torque was revised in accordance with the corrected helix angles. For gears with 39°helix-hand, it does not allow you to calculate the gear strength on our Web Catalog. Please use the GCSW, the gear calculation software available for the calculation.	12.01.19	.
P470	The item “Bore” in the Dimension Table for Zerol Bevel Gears	A --> A H7	11.05.16	.
P476	SB2-6012	Correction in Length of bore / shaft 24 --> 27	11.10.07	.
P482	DB products	Correction in Bore ~~AH7~~ --> A	11.11.9	.
P541	Dimension table for BG Bronz Worm Wheels	The items(fields) below are corrected ~~Web thickness~~ --> Mounting distance The field of "Web O.D." and "Mounting distance" are combined and changed to the field "Set Screw" (H) changed to J (I）changed to size J changed to L	11.10.11	.
P555	Web thickness for CG5-60R1	Web thickness ~~(13)~~ --> (14)	11.05.24	.
P582	GC Products The caution notes No.1 and No.3 described at "Caution on Product Characteristics"	(1) ~~'"S" denotes minimum bore products. Inner hubs come with snap rings and set screws.~~ (Changed as below) S-type products are of minimum bore products. For products with a snap ring and a tapped hole, a set screw is included as an accessory. (3)Since Uni-chromate treatment is applied, there may be some changes in dimensions of bore, keyway etc., decreasing by a few μｍ..	11.04.15	.
P765 - 768	The index pages of Technical Reference Guide	The page numbers shown in the index pages were incurrent as the information was for the previous version of the reference.	12.01.26	.