KHK Stock Gears 3013
140/452

138SpurGearsHelicalGearsInternalGearsRacksCP Racks& PinionsMiterGearsBevelGearsScrewGearsWormGear PairBevelGearboxesOtherProductsPlastic Spur Gears with Stainless Steel CoreModule 1、1.5、2PUEFBCDGHAMC901SUS303S1[Caution on Product Characteristics]① Significant variations in temperature or humidity can cause dimensional changes in plastic gears (MC Nylon gears), including bore size (H8 when pro-duced), tooth diameter, and backlash. Please see the section “Design of Plastic Gears” in separate technical reference book. (Page 101).② The allowable torques shown in the table are calculated values according to the assumed usage conditions. Please see Page 31 for more details.③ When the core O.D is the same as the hub diameter, you may see some serration on the hub. There is no effect on the strength of the gear.④ Without lubrication, using plastic gears in pairs may generate heat and dilation. It is recommended to mate them with steel gears.⑤ The backlash values shown in the table are the theoretical values for the backlash in the normal direction of a pair of identical gears in mesh.23457102030405070005000400030002000100023457102030405020304050701002003004005007001000■ Denition of Holding Strength and Safety Factor① The holding strength between the metal core and the molded material is a function of the contact area. The relationship between the core outside diameter and the radial strength (torque) is shown on the left, while the relationship between the core diameter and the resis-tant thrust force is shown on the right.Radial Strength(Kfg.m per cm of Contact Surface Width)■ Relationship between radial strength and core diameterCore O.D.(cm)■ Relationship between resistant thrust force and core diameterResistant Thrust Force (Kgf. Per cm of Contact Surface Width)Core O.D.(cm)Catalog No.No. of teethShapeBoreHub dia.Pitch dia.Outside dia.Metal core dia.Allowable torque (N·m)Allowable torque (kgf·m)BacklashWeightAH7BCDHBending strengthBending strength(mm)(kg)*The precision grade of J Series products is equivalent to the value shown in the table.PU1-3030S18203032201.030.100~0.340.046 PU1-3535253537251.250.130.074 PU1-404010254042281.480.150.081 PU1-5050305052341.960.200.13 PU1-6060406062452.410.250~0.360.22 PU1-8080408082453.340.340.25 PU1.5-3030304548303.460.350~0.380.15 PU1.5-35353352.555.5364.220.430~0.400.20 PU1.5-4040406063455.000.510.31 PU1.5-505012407578456.600.670.33 PU1.5-6060509093558.140.830.51 PU1.5-8080601201238511.261.150~0.421.00 PU2-202010224044224.910.500.10 PU2-2525305054306.540.670.20 PU2-3030356064358.200.840~0.440.28 PU2-3535124070744510.01.020.41 PU2-4040155580846011.91.210.70 PU2-5050601001046515.71.600.88 PU2-6060601201248519.31.970~0.461.28SpecificationsPrecision gradeJIS grade N9 (JIS B1702-1: 1998)*JIS grade 5 (JIS B1702: 1976) Gear teethStandard full depthPressure angle20°MaterialMC901 with SUS303 coreHeat treatment ―Tooth hardness(115~120HRR)Modulem1m1.5m2Face width (E)101520Hub width (F)101214Total length (G)202734Screw offset (J)567[Caution on Secondary Operations]① Please read “Caution on Performing Secondary Operations” (Page 32) when performing modifications and/or secondary operations for safety con-cerns. KHK Quick-Mod Gears, the KHK's system for quick modification of KHK stock gears is also available.② Even though the holding strength at the material interface is designed to be stronger than the teeth, a secondary operation may weaken the holding strength.③ Plastic gears are susceptible to the effects of temperature and moisture. Dimensional changes may occur while performing secondary operations and during post-machining operations.

元のページ 

10秒後に元のページに移動します

※このページを正しく表示するにはFlashPlayer10.2以上が必要です