KHK Stock Gears 3013
158/452

156SpurGearsHelicalGearsInternalGearsRacksCP Racks& PinionsMiterGearsBevelGearsScrewGearsWormGear PairBevelGearboxesOtherProductsBrass Spur GearsModule 0.5BSSSpecificationsPrecision gradeJIS grade N8 (JIS B1702-1: 1998)*JIS grade 4 (JIS B1702: 1976) Gear teethStandard full depthPressure angle20°MaterialFree cutting brass(C3604)Heat treatment ―Tooth hardness(more than 80HV)Catalog No.ModuleNo. of teethShapeBoreHub dia.Pitch dia.Outside dia.Face widthHub widthTotal lengthKeywayAH7BCDEFGWidth×DepthBSS0.5-15Am0.515S3T38.57.58.531114―BSS0.5-16A16S3T398931114―BSS0.5-17A17S3T39.58.59.531114―BSS0.5-18A18S3T31091031114―BSS0.5-19A19S3T310.59.510.531114―BSS0.5-20BSS0.5-20ABSS0.5-20B20S1S3TS3T4348.511111011371111101414―――BSS0.5-21A21S3T311.510.511.531114―BSS0.5-22A22S1T3911123710―BSS0.5-23A23S1T3911.512.53710―BSS0.5-24A24S1T31012133710―BSS0.5-24B24S1T41012133710―BSS0.5-25BSS0.5-25ABSS0.5-25B25S1S1TS1T43411101012.513.53710―――BSS0.5-26A26S1T31013143710―BSS0.5-27A27S1T31013.514.53710―BSS0.5-28A28S1T31214153710―BSS0.5-29A29S1T31214.515.53710―BSS0.5-30BSS0.5-30ABSS0.5-30BBSS0.5-30C30S1S1TS1TS1T43451312121215163710――――BSS0.5-32A32S1T41416173710―BSS0.5-34A34S1T41517183710―BSS0.5-35A35S1T41517.518.53710―BSS0.5-36A36S1T41618193710―BSS0.5-38A38S1T41619203710―BSS0.5-40BSS0.5-40ABSS0.5-40B40S1S1TS1T44517181820213710―――BSS0.5-50ABSS0.5-50B50S1TS1T45222225263710――BSS0.5-60ABSS0.5-60B60S1TS1T56282830313710――BSS0.5-70ABSS0.5-70B70S1TS1T56282835363710――BSS0.5-80ABSS0.5-80B80S1TS1T56282840413710――GEFJACDS3T*The precision grade of products with a module of less than 0.8 is equivalent to the value shown in the table.[Caution on Product Characteristics]① For products with a tapped hole, a set screw is included.② The allowable torques shown in the table are calculated values according to the assumed usage conditions. Please see Page 31 for more details.③ The backlash values shown in the table are the theoretical values for the backlash in the normal direction of a pair of identical gears in mesh.④ If diameter is less than φ 4, the diameter tolerance is H8. If diameter is φ 5 or φ 6, and the hole length exceeds 3 times of the diameter, the tolerance is also H8.*For products not categorized in our KHK Stock Gear series, custom gear production services with short lead times is available. For details see Page 8.

元のページ 

10秒後に元のページに移動します

※このページを正しく表示するにはFlashPlayer10.2以上が必要です